Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Steel cutting machine proper use and safety precau...

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Steel cutting machine proper use and safety precau...: 1. Pick countertop material should be level and lower cutter, table length can be determined according to the length of the workpiece. 2. ...

Steel cutting machine proper use and safety precautions

1. Pick countertop material should be level and lower cutter, table length can be determined according to the length of the workpiece.
2. Before starting, you should check to make sure no cracks Steel cutting machine, turret bolt, solid shield. Then rotate the pulley by hand to check the gear meshing clearance, adjust the cutter gap.
3. After starting, you should first dry run, check after each transmission parts and bearings in normal operation only after the job.
4. machinery does not reach normal operating speed may not cut material. When cutting, use the cutter, the lower parts of the alignment edge grip reinforced quickly put, the operator should stand on the side of force to suppress the fixed blade steel, should be reinforced to prevent the end of the pop-up hurt. It is prohibited on both sides of the blade with both hands holding the steel sub-leaning feeding.
5. Do not cut diameter and strength than mechanical nameplate steel and red-hot steel. Once cut off when a plurality of reinforcement, the total cross-sectional area should be within the specified range.
6. Cut low-alloy steel, replace the high hardness cutter,   Steel cutting machine plate diameter should be consistent with the provisions.
7. When cutting short material, distance between the hand and the knife should be maintained at 150mm or more, such as hand side is less than 400mm, you should use short steel casing or jig head pinched or folder in prison.
8. The operation is prohibited by hand directly decapitation and remove debris near the cutter. Rebar cutter swing around and around, can not stay non-operators.
9. When they find machinery not functioning properly, abnormal noise or skew cutter, you should immediately downtime.
10. After the job, you should cut off the power, steel brush to remove debris between the cutter, carry out the whole cleaning lubrication.
11. A hydraulic drive front Steel cutting machine operation, check that the hydraulic oil and motor rotation direction to meet the requirements. After starting, you should load operation, loose open valve, drain the body of the air cylinder net, before proceeding cut tendons.

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Steel cutting machine is essential for steel proce...

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Steel cutting machine is essential for steel proce...: Steel cutting machine  is one of the indispensable steel processing equipment, which is mainly terms housing construction, bridges, tunnels,...

Steel cutting machine is essential for steel processing equipment

Steel cutting machine is one of the indispensable steel processing equipment, which is mainly terms housing construction, bridges, tunnels, power plants, large-scale water conservancy projects for steel and Cutting. Steel cutting machine compared with other cutting equipment, light weight, low energy consumption, reliable operation, high efficiency, so in recent years gradually been widely used machining and small rolling mills, etc., in various fields of national economy played an important role.

Contrast Steel cutting machine at home and abroad:
Due to the low-tech cutting machine, easy to counterfeit, not the reasons for higher profits, so the manufacturers basically maintain the status quo for decades, the development of unpleasant, compared with foreign counterparts specifically the following aspects gap.
Construction of rapid development of the global economy for the construction industry, in particular to provide a broad development space for the development of construction machinery, for the majority of enterprises to provide a stage to show their. Faced with increasingly fierce competition in China's construction machinery market, strengthen enterprise management, investments in technology, emphasis on new technology, research and development of new products, improve product quality and service levels, and actively take the initiative to market, so that enterprises products continue to meet the needs of users, shorten the gap with foreign advanced enterprises as soon as possible, it is undoubtedly the only way our country Steel cutting machine manufacturing enterprises survival and development.

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Cutting machine for use services to seek a breakth...

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Cutting machine for use services to seek a breakth...:        There are plans, quality of service, can also reach the market spread and enhance the brand effect. After 10 years of rapid growth,...

Cutting machine for use services to seek a breakthrough

       There are plans, quality of service, can also reach the market spread and enhance the brand effect.
After 10 years of rapid growth, as of the end of 2015, China's construction machinery industry has grown into the world's largest single market, accounting for 48 percent of the globe. With the changes in the global market and China's economic development, construction machinery industry is the summer to winter, scale expansion of growth model is challenged, Cutting machine falling demand so that the industry is suffering from overcapacity dilemma. So how to change the status quo?
       Engineering machinery and general consumer goods are the two concepts. For general consumer goods, the service may not be one of service packages, but one of the construction machinery industry in the service itself is the product attributes. Since the device itself and the use of sophisticated and complicated mining of the severity, starting from the customer to get the equipment, for maintenance of equipment, operation and maintenance are required to do a lot of Doosan guidance, support work. Therefore, the machinery industry and services, and sell products almost Aioi accompanied.
Chinese construction Cutting machine industry has been the last 10 years of rapid growth, the market although rapid development, but the industry is not mature enough and has broken down. Market demand and high tightening business development goals, even more intensified competition among construction machinery industry. In order to find more space for development, it should be in addition to product competition and price competition, seeking to use the service to create brand differentiation. For example, with service branding competitive construction machinery industry, with customers to establish a close and long-term relationships, strengthen the leadership position in the industry.
       You can start the construction machinery market-oriented inspection activities, Cutting machine that is a customer, the customer's equipment is the core, many customers are equipped to do business around him. Arrived at the scene, in addition to equipment for maintenance, but also on the surrounding equipment servicing, the final actual result should be practical about three times the number of units.

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Steel cutting machine operator should have the job...

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Steel cutting machine operator should have the job...:     On many construction sites, says this will be a slogan, it is happy to go to work, safe on home. This is to remind staff of the constru...

Steel cutting machine operator should have the job functions

    On many construction sites, says this will be a slogan, it is happy to go to work, safe on home. This is to remind staff of the construction site, always in my heart the safety in production. Cutting steel, it is to use a professional Steel cutting machine equipment, will cut steel shapes, of varying lengths, varying thickness steel accessories. Here, we look at the process steel cutting machine operator should have used what job functions

    First, workers to operate steel cutting machines, construction sites to keep in mind about on-site construction management system of regulations, strictly in accordance with the security process to regulate the operation of cutting machines. There is the best choice for young men operate this equipment between twenty to four years old. Because the work itself has some risk, while also requiring the operator energetic, thought highly concentrated, the older, tired workers to operate, and is not competent for the job. It also requires the operator workers go to work, wearing the necessary protective clothing operation Steel cutting machine equipment. There is a day before turning to the no-load of the premise, commissioning one to five minutes, when it is determined there is no abnormal noise, before starting work.

    Second, workers to operate steel cutting machine, requiring all staff posts, should also hold a health certificate and cutter appointment card, and during working hours and can not leave cutter jobs, so people are not familiar with the equipment malfunction of equipment, cause unnecessary harm.

    In addition, it should also pay attention to three points. First, we must pay attention to all the operations on the ground to try to complete; the second is to pay attention to when handling steel, do not touch the power outlet to prevent electric shock; the third is after the end of each working day to add oil to the device active portion, Steel cutting machine to extend the life of the equipment.

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: The steel cutting machine projects social impacts

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: The steel cutting machine projects social impacts:       1 The analysis of the effects of social impact. Develop social impact and social benefits of the project construction of the cutting ...

The steel cutting machine projects social impacts

      1 The analysis of the effects of social impact. Develop social impact and social benefits of the project construction of the cutting machine proposed steel and operating activities in the project sites that may arise.
      2. Social Adaptability. analysis of steel cutting machine if the project proposed by the local social environment, cultural acceptance conditions, evaluation of the project with the local social environment of mutual adaptation.
      3 Social risks and countermeasures. Social risk factors for a variety of social Steel cutting machine involved in the project analysis, the relationship with the local community to avoid social risks, and promote the smooth implementation of the program of coordinated measures projects projects.
      Of course, the economic impact of steel cutting machine and society should be more than that and some other things to keep in mind here is not to enumerate.

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Why steel cutting machine would be decapitated, to...

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Why steel cutting machine would be decapitated, to...: 1, since the case is casting the production, casting prone to internal porosity, trachoma and low density; 2, knife slide design on the ce...

Why steel cutting machine would be decapitated, torn four reasons

1, since the case is casting the production, casting prone to internal porosity, trachoma and low density;
2, knife slide design on the center line on the left side instead of the front and rear of the cutter housing, the cutter is runningSteel cutting machine is easy to swing and shake;
3, the opening hole on the left side of the crankshaft and a large cut above the slide housing is connected, together with three holes to make the left side of the housing slowdown basically lost the carrying capacity;
4,Steel cutting machine users are mostly trained personnel without mechanical operation, refueling and do not bother to use the tool change.
Yongyi Tongfeng steel cutting machine to produce excellent welding technology, will not be decapitated cutting machine, affirmation by the customer, whether it is in the shape of the material, or process exists Steel cutting machine advantage if you intend to purchase in the industry , then contact the site customer service or call us directly Yongyi Tongfeng.

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Maintenance points steel cutting machine equipment...

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Maintenance points steel cutting machine equipment...: Maintenance points a day after the work is completed, to develop promptly clean up the habit of  Steel cutting machine  tools, cutting tools...

Maintenance points steel cutting machine equipment mainly

Maintenance points a day after the work is completed, to develop promptly clean up the habit of Steel cutting machine tools, cutting tools around the same time to all kinds of debris piled up, one by one classify clean up and keep clean the entire cutting machine. At the same time, to use special tools for cutting machine all bolts and screws, reinforcement, tighten and stick cutting machine internal feed belt is loose? If so, to timely adjust. There is to check the prop wear, timely blunt tool replacement.

Maintenance Point # 2, when Steel cutting machine used continuously over four hundred to five hundred hours, necessary and timely periodic maintenance of equipment. For example, add the oil, adjust the tool space, check the eccentricity of the bearing and gears and so on. Need to remind the operator to note that in winter, cutting machine ZG-2 is best to use oil. This type of lubricant relatively thin, more suitable for winter use; in summer, Steel cutting machine is best to use the number ZG-4 grease. This type of lubricating oil more viscous, more suitable for summer use.

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Automatic identification and automatic integration...

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Automatic identification and automatic integration...: Features  Steel cutting machine , it clearly shows us its automatic control at work, saving time and effort simply do not tell the length of...

Automatic identification and automatic integration of Steel cutting machine

Features Steel cutting machine, it clearly shows us its automatic control at work, saving time and effort simply do not tell the length of its press wheels do not need to enter the number of pulses, reflected in its excellent performance this time automatic identification and automatic integration of professional work.
In addition, the interior design can reach the safe operation of Steel cutting machine, wherein the interior of the electrical board, more than a layer designed to prevent dust or the conductive material to achieve fall into the danger of accidents caused by accidental short circuit. And this machine does not need frequent repairs, even when the repair is also very convenient. Of course, it's another laudable feature is its output more than one point, the generalSteel cutting machine will be arranged to three, this advantage is capable of preventing an unexpected point of failure occurs, change to another point in time work .

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Select Yongyi Tongfeng choose Steel cutting machin...

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Select Yongyi Tongfeng choose Steel cutting machin...:      First, select the first look at the quality of  Steel cutting machine Quality is the most critical factor in a product, but also a dec...

Select Yongyi Tongfeng choose Steel cutting machine

     First, select the first look at the quality of Steel cutting machine
Quality is the most critical factor in a product, but also a decisive factor. Consumers choose the time, the first note is whether the product quality to meet the standards of their hearts, and then to consider other factors, compared with other aspects. Steel cutting machine, too, when the manufacturer of choice, we must pay attention to the manufacturer's credibility and reputation in the customer mouth how to determine whether the quality of steel cutting machine is more at ease and to be personally acquainted with your machine to see its quality Quality is the result of all the work conditions.
     Second, selectSteel cutting machine followed to see prices
Different from different manufacturers work efficiency, cost is also high and low used, therefore, in terms of price is affected by many factors. In the Select steel cutting machine, when what I should pay attention to whether the price is reasonable or observe what factors influence the price of being. Prices of steel bending machine is one of the final product cost factors, choose a more affordable price in order to increase profits and efficiency of the final product, in order to ensure the smooth functioning of the enterprise. So, we choose steel cutting machine, pay attention to shop around, choose lower prices, higher quality products as a corporate good assistant.
     Third, chooseSteel cutting machine finally see sale
Steel bending machine as a conventional machine, has the disadvantage of consuming the body during use, there will be a lot of problems when in use. After then, when customers encountered some problems when the sale, the first thought must be to sell the machine manufacturers, therefore, as a good corporate services, in after-sales service must do a good job, to ensure that customers buy steelcutting machine No worries.
    Therefore, we in the choice of steel cutting machine manufacturers must pay attention to these issues.