Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Steel cutting machine proper use and safety precau...

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Steel cutting machine proper use and safety precau...: 1. Pick countertop material should be level and lower cutter, table length can be determined according to the length of the workpiece. 2. ...

Steel cutting machine proper use and safety precautions

1. Pick countertop material should be level and lower cutter, table length can be determined according to the length of the workpiece.
2. Before starting, you should check to make sure no cracks Steel cutting machine, turret bolt, solid shield. Then rotate the pulley by hand to check the gear meshing clearance, adjust the cutter gap.
3. After starting, you should first dry run, check after each transmission parts and bearings in normal operation only after the job.
4. machinery does not reach normal operating speed may not cut material. When cutting, use the cutter, the lower parts of the alignment edge grip reinforced quickly put, the operator should stand on the side of force to suppress the fixed blade steel, should be reinforced to prevent the end of the pop-up hurt. It is prohibited on both sides of the blade with both hands holding the steel sub-leaning feeding.
5. Do not cut diameter and strength than mechanical nameplate steel and red-hot steel. Once cut off when a plurality of reinforcement, the total cross-sectional area should be within the specified range.
6. Cut low-alloy steel, replace the high hardness cutter,   Steel cutting machine plate diameter should be consistent with the provisions.
7. When cutting short material, distance between the hand and the knife should be maintained at 150mm or more, such as hand side is less than 400mm, you should use short steel casing or jig head pinched or folder in prison.
8. The operation is prohibited by hand directly decapitation and remove debris near the cutter. Rebar cutter swing around and around, can not stay non-operators.
9. When they find machinery not functioning properly, abnormal noise or skew cutter, you should immediately downtime.
10. After the job, you should cut off the power, steel brush to remove debris between the cutter, carry out the whole cleaning lubrication.
11. A hydraulic drive front Steel cutting machine operation, check that the hydraulic oil and motor rotation direction to meet the requirements. After starting, you should load operation, loose open valve, drain the body of the air cylinder net, before proceeding cut tendons.

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Steel cutting machine is essential for steel proce...

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Steel cutting machine is essential for steel proce...: Steel cutting machine  is one of the indispensable steel processing equipment, which is mainly terms housing construction, bridges, tunnels,...

Steel cutting machine is essential for steel processing equipment

Steel cutting machine is one of the indispensable steel processing equipment, which is mainly terms housing construction, bridges, tunnels, power plants, large-scale water conservancy projects for steel and Cutting. Steel cutting machine compared with other cutting equipment, light weight, low energy consumption, reliable operation, high efficiency, so in recent years gradually been widely used machining and small rolling mills, etc., in various fields of national economy played an important role.

Contrast Steel cutting machine at home and abroad:
Due to the low-tech cutting machine, easy to counterfeit, not the reasons for higher profits, so the manufacturers basically maintain the status quo for decades, the development of unpleasant, compared with foreign counterparts specifically the following aspects gap.
Construction of rapid development of the global economy for the construction industry, in particular to provide a broad development space for the development of construction machinery, for the majority of enterprises to provide a stage to show their. Faced with increasingly fierce competition in China's construction machinery market, strengthen enterprise management, investments in technology, emphasis on new technology, research and development of new products, improve product quality and service levels, and actively take the initiative to market, so that enterprises products continue to meet the needs of users, shorten the gap with foreign advanced enterprises as soon as possible, it is undoubtedly the only way our country Steel cutting machine manufacturing enterprises survival and development.

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Cutting machine for use services to seek a breakth...

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Cutting machine for use services to seek a breakth...:        There are plans, quality of service, can also reach the market spread and enhance the brand effect. After 10 years of rapid growth,...

Cutting machine for use services to seek a breakthrough

       There are plans, quality of service, can also reach the market spread and enhance the brand effect.
After 10 years of rapid growth, as of the end of 2015, China's construction machinery industry has grown into the world's largest single market, accounting for 48 percent of the globe. With the changes in the global market and China's economic development, construction machinery industry is the summer to winter, scale expansion of growth model is challenged, Cutting machine falling demand so that the industry is suffering from overcapacity dilemma. So how to change the status quo?
       Engineering machinery and general consumer goods are the two concepts. For general consumer goods, the service may not be one of service packages, but one of the construction machinery industry in the service itself is the product attributes. Since the device itself and the use of sophisticated and complicated mining of the severity, starting from the customer to get the equipment, for maintenance of equipment, operation and maintenance are required to do a lot of Doosan guidance, support work. Therefore, the machinery industry and services, and sell products almost Aioi accompanied.
Chinese construction Cutting machine industry has been the last 10 years of rapid growth, the market although rapid development, but the industry is not mature enough and has broken down. Market demand and high tightening business development goals, even more intensified competition among construction machinery industry. In order to find more space for development, it should be in addition to product competition and price competition, seeking to use the service to create brand differentiation. For example, with service branding competitive construction machinery industry, with customers to establish a close and long-term relationships, strengthen the leadership position in the industry.
       You can start the construction machinery market-oriented inspection activities, Cutting machine that is a customer, the customer's equipment is the core, many customers are equipped to do business around him. Arrived at the scene, in addition to equipment for maintenance, but also on the surrounding equipment servicing, the final actual result should be practical about three times the number of units.

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Steel cutting machine operator should have the job...

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Steel cutting machine operator should have the job...:     On many construction sites, says this will be a slogan, it is happy to go to work, safe on home. This is to remind staff of the constru...

Steel cutting machine operator should have the job functions

    On many construction sites, says this will be a slogan, it is happy to go to work, safe on home. This is to remind staff of the construction site, always in my heart the safety in production. Cutting steel, it is to use a professional Steel cutting machine equipment, will cut steel shapes, of varying lengths, varying thickness steel accessories. Here, we look at the process steel cutting machine operator should have used what job functions

    First, workers to operate steel cutting machines, construction sites to keep in mind about on-site construction management system of regulations, strictly in accordance with the security process to regulate the operation of cutting machines. There is the best choice for young men operate this equipment between twenty to four years old. Because the work itself has some risk, while also requiring the operator energetic, thought highly concentrated, the older, tired workers to operate, and is not competent for the job. It also requires the operator workers go to work, wearing the necessary protective clothing operation Steel cutting machine equipment. There is a day before turning to the no-load of the premise, commissioning one to five minutes, when it is determined there is no abnormal noise, before starting work.

    Second, workers to operate steel cutting machine, requiring all staff posts, should also hold a health certificate and cutter appointment card, and during working hours and can not leave cutter jobs, so people are not familiar with the equipment malfunction of equipment, cause unnecessary harm.

    In addition, it should also pay attention to three points. First, we must pay attention to all the operations on the ground to try to complete; the second is to pay attention to when handling steel, do not touch the power outlet to prevent electric shock; the third is after the end of each working day to add oil to the device active portion, Steel cutting machine to extend the life of the equipment.

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: The steel cutting machine projects social impacts

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: The steel cutting machine projects social impacts:       1 The analysis of the effects of social impact. Develop social impact and social benefits of the project construction of the cutting ...

The steel cutting machine projects social impacts

      1 The analysis of the effects of social impact. Develop social impact and social benefits of the project construction of the cutting machine proposed steel and operating activities in the project sites that may arise.
      2. Social Adaptability. analysis of steel cutting machine if the project proposed by the local social environment, cultural acceptance conditions, evaluation of the project with the local social environment of mutual adaptation.
      3 Social risks and countermeasures. Social risk factors for a variety of social Steel cutting machine involved in the project analysis, the relationship with the local community to avoid social risks, and promote the smooth implementation of the program of coordinated measures projects projects.
      Of course, the economic impact of steel cutting machine and society should be more than that and some other things to keep in mind here is not to enumerate.

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Why steel cutting machine would be decapitated, to...

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Why steel cutting machine would be decapitated, to...: 1, since the case is casting the production, casting prone to internal porosity, trachoma and low density; 2, knife slide design on the ce...

Why steel cutting machine would be decapitated, torn four reasons

1, since the case is casting the production, casting prone to internal porosity, trachoma and low density;
2, knife slide design on the center line on the left side instead of the front and rear of the cutter housing, the cutter is runningSteel cutting machine is easy to swing and shake;
3, the opening hole on the left side of the crankshaft and a large cut above the slide housing is connected, together with three holes to make the left side of the housing slowdown basically lost the carrying capacity;
4,Steel cutting machine users are mostly trained personnel without mechanical operation, refueling and do not bother to use the tool change.
Yongyi Tongfeng steel cutting machine to produce excellent welding technology, will not be decapitated cutting machine, affirmation by the customer, whether it is in the shape of the material, or process exists Steel cutting machine advantage if you intend to purchase in the industry , then contact the site customer service or call us directly Yongyi Tongfeng.

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Maintenance points steel cutting machine equipment...

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Maintenance points steel cutting machine equipment...: Maintenance points a day after the work is completed, to develop promptly clean up the habit of  Steel cutting machine  tools, cutting tools...

Maintenance points steel cutting machine equipment mainly

Maintenance points a day after the work is completed, to develop promptly clean up the habit of Steel cutting machine tools, cutting tools around the same time to all kinds of debris piled up, one by one classify clean up and keep clean the entire cutting machine. At the same time, to use special tools for cutting machine all bolts and screws, reinforcement, tighten and stick cutting machine internal feed belt is loose? If so, to timely adjust. There is to check the prop wear, timely blunt tool replacement.

Maintenance Point # 2, when Steel cutting machine used continuously over four hundred to five hundred hours, necessary and timely periodic maintenance of equipment. For example, add the oil, adjust the tool space, check the eccentricity of the bearing and gears and so on. Need to remind the operator to note that in winter, cutting machine ZG-2 is best to use oil. This type of lubricant relatively thin, more suitable for winter use; in summer, Steel cutting machine is best to use the number ZG-4 grease. This type of lubricating oil more viscous, more suitable for summer use.

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Automatic identification and automatic integration...

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Automatic identification and automatic integration...: Features  Steel cutting machine , it clearly shows us its automatic control at work, saving time and effort simply do not tell the length of...

Automatic identification and automatic integration of Steel cutting machine

Features Steel cutting machine, it clearly shows us its automatic control at work, saving time and effort simply do not tell the length of its press wheels do not need to enter the number of pulses, reflected in its excellent performance this time automatic identification and automatic integration of professional work.
In addition, the interior design can reach the safe operation of Steel cutting machine, wherein the interior of the electrical board, more than a layer designed to prevent dust or the conductive material to achieve fall into the danger of accidents caused by accidental short circuit. And this machine does not need frequent repairs, even when the repair is also very convenient. Of course, it's another laudable feature is its output more than one point, the generalSteel cutting machine will be arranged to three, this advantage is capable of preventing an unexpected point of failure occurs, change to another point in time work .

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Select Yongyi Tongfeng choose Steel cutting machin...

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Select Yongyi Tongfeng choose Steel cutting machin...:      First, select the first look at the quality of  Steel cutting machine Quality is the most critical factor in a product, but also a dec...

Select Yongyi Tongfeng choose Steel cutting machine

     First, select the first look at the quality of Steel cutting machine
Quality is the most critical factor in a product, but also a decisive factor. Consumers choose the time, the first note is whether the product quality to meet the standards of their hearts, and then to consider other factors, compared with other aspects. Steel cutting machine, too, when the manufacturer of choice, we must pay attention to the manufacturer's credibility and reputation in the customer mouth how to determine whether the quality of steel cutting machine is more at ease and to be personally acquainted with your machine to see its quality Quality is the result of all the work conditions.
     Second, selectSteel cutting machine followed to see prices
Different from different manufacturers work efficiency, cost is also high and low used, therefore, in terms of price is affected by many factors. In the Select steel cutting machine, when what I should pay attention to whether the price is reasonable or observe what factors influence the price of being. Prices of steel bending machine is one of the final product cost factors, choose a more affordable price in order to increase profits and efficiency of the final product, in order to ensure the smooth functioning of the enterprise. So, we choose steel cutting machine, pay attention to shop around, choose lower prices, higher quality products as a corporate good assistant.
     Third, chooseSteel cutting machine finally see sale
Steel bending machine as a conventional machine, has the disadvantage of consuming the body during use, there will be a lot of problems when in use. After then, when customers encountered some problems when the sale, the first thought must be to sell the machine manufacturers, therefore, as a good corporate services, in after-sales service must do a good job, to ensure that customers buy steelcutting machine No worries.
    Therefore, we in the choice of steel cutting machine manufacturers must pay attention to these issues.

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Steel cutting machine Detailed

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Steel cutting machine Detailed: With the development of technology, the industry has also ushered in the country's development opportunities, such as the construction i...

Steel cutting machine Detailed

With the development of technology, the industry has also ushered in the country's development opportunities, such as the construction industry, to usher in a great development. For the development of the construction industry to make a significant contribution to the necessary number ofSteel cutting machine, which is a rise in recent years of the machine, widely used in various industries among which the most widely used in the construction industry, a major field indispensable part of it. But many of my friends still do not quite understand this machine, follow Yongyi Tongfeng today we take a look at the main features is to understand it!

Now Steel cutting machine has been further developed, can be divided into fully automatic and semi-automatic cutting machine cutting machine, a fully automated, one is automatically added to the artificial, the main difference between the two here. Automatic cutting machine is mainly used to cut rebar cutter, and semi-automatic manual control is cut reinforcement.Steel cutting machine in the daily work being mainly used to cut steel, angle steel and other types of steel, the working efficiency is very high, and it is very easy to use, only need to add one oil can be prolonged use, machinery is fully capable in very good condition. And now we often add a little oil, lubrication conditions will be greatly improved.

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: It requires the development of future steel cuttin...

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: It requires the development of future steel cuttin...: Prospects  Steel cutting machine  is very good, mainly because the market demand for large, small competition, so the whole market is still...

It requires the development of future steel cutting machine

Prospects Steel cutting machine is very good, mainly because the market demand for large, small competition, so the whole market is still very good. With the economic development, the future needs of steel cutting machine will further increase, which is necessary to meet the market demand for. It is mainly in such aspects:
First, the market demand, because this device it is currently one of the most advanced equipment, many companies are upgrading, accelerate its replacement, because steel cutting machine can make up for many deficiencies, greatly increasing the efficiency of the work.
Second, the global warming economy, the domestic market is very active in foreign markets is also thriving scene appears, which is very good.
  In a conventional Steel cutting machine development, there is a great shortage lies not withstand excessive load, but not all aspects of the design is very reasonable, most are processed by hand, the price is relatively high, relatively poor performance does not meet the Modern society needs, so the traditional cutting machine or application is not stopped, as it has no market. Now pursue paint spraying, color is very scientific, appearance do not see weld gap and sharp corners, etc., it is very smooth and clean, beautiful, well received by customers like.
  Steel cutting machine is a good development, it can be said the rapid economic development is inseparable from the future application of steel cutting machine, especially in great demand in the construction sector. With advances in technology, processes steel cutting machine is also rising, produced by the steel cutting machine has also been greatly improved, can be said to be very good, I believe the future will be better development.

How to make Rod cutting machine cutting precision minimized?

       Before examining factors GQ52 Rod Cutting Machine cutting precision, we need to briefly explain the working principle of steel cutting machine, which is by the motor via a belt drive growth, make high-speed rotation tune straight through the transfer will be transferred straight steel straight, straight mold remove rust by steel surface of the skin, then motor through another pair of belts and gear box reduction effect, while you can drive two transport roller, traction bars forward movement, while you can crank wheel drive so that the hammer up and down motion.
       This process, when the reinforcing bars until a predetermined length, hammer hammering on the turret, steel can be successfully cut. In order to be able to complete the cycle when the device action, cutting steel falls by rack, since the spring action, knife sets general will return to its original position. This is the basic workflowSteel cutting machine, then the impact of steel cutting machine cutting precision of factors?
       First, the base material of different materials steel is the most fundamental factors for the steel cutting machine equipment, even the same material, if the composition of the material of different cutting accuracy will vary. Second, the impact of different diameter steel base material size on the cutting accuracy can not be ignored, because of different diameter steel cutting precision allowed deviation is completely different.
       In addition, different construction sites require precision steel processing will be different, which is also one of the steel cutting machine cutting precision factor. In fact, when the actual control of the operator of such equipment, the effect of skilled staff work between employees and unskilled will have a very significant difference, which directly relates to Cutting Machinefunction achieve what cutting accuracy.

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Rod Cutting Machines formal method of operation

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Rod Cutting Machines formal method of operation: Before using the first Rod Cutting Machines must be sure the work surface and the cutter is not kept below the level of the state, if not,...

Rod Cutting Machines formal method of operation

Before using the first Rod Cutting Machines must be sure the work surface and the cutter is not kept below the level of the state, if not, the first thing to do is to adjust the level, then check the cutter steel cutter There are no abnormal phenomenon, for example, there is no crack crack, screw fastening tool is not, but also turned by hand at the pulley, check the top of the backlash is not appropriate, and if we find inappropriate, first adjust better.
Plug in the power, the start time, do not worry now operating on steel, should first dry run for a while, take a look at every part of the operation is not a normal Rod Cutting Machines, to determine a good no anomalies, then you can really start operate. In the cut material time, pay more attention to the correctness of the staff is a hand operation, and posture on. Middle and lower use of Rod Cutting Machines should cutter, hand grip bars to the staff, and aligning the entrance of the cutter. If you are a person to operate it, the staff must be fixed position, can only stand on the side of the blade and hard pressed steel, in the course of their work should not arbitrarily change position, to avoid wounding steel.
If the Rod Cutting Machines can not be more than a one-time cut rebar, then do not do it abruptly, range of different steel cutting machine has a work must be able to ensure the safety of staff inside the operating range.

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Rod cutting machine Highlights

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter: Rod cutting machine Highlights: (1) Before using Rod cutting machine  , to check the blade is firmly installed, the gap is appropriate, transmission system, the relative m...

Rod cutting machine Highlights

(1) Before using Rod cutting machine , to check the blade is firmly installed, the gap is appropriate, transmission system, the relative moving part. Points lubrication is good, the last load test run, after confirmation before the official start of operations.
(2) the level of the fixed and movable blade gap should be maintained 0.5 ~ 1.0 mm, if the level of the gap is too large reinforced ends of the cut prone horseshoe. The amount of overlap of the two blades to be determined in accordance with the cut rebar diameter. Usually when cutting diameter less than 20 mm, blade vertical clearance is 1 ~ 2 mm, cut off 20 mm diameter greater than or equal to about 5mm. Increase or decrease the fixed blade clearance adjustable pad behind the blade.
(3) When cutting steel, the operator should hand grip bars, and other activities when the return blade into steel, reinforced to prevent the end of the swing or pop wounding.
(4) lead to be cut to the cut steel vertical and flat, the length of use pliers material into short steel blade when cutting 300mm or less, are not allowed direct hand feeding.
(5) exceeds a predetermined cutter diameter steel or chemical components in the steel over steel, steel and other burning red are not allowed off the plane.
(6) Rod cutting machine during operation, do not touch the cleaning blade above the dust accumulation, debris and found the sound is not working properly, the blade poor adhesion, etc., should immediately stop inspection, repair, until after commissioning, They are allowed to continue to use.
(7) Before using the hydraulic Rod cutting machine , to check the oil level and the motor rotation direction. Methods: Pine oil valve open, no-load operation 2min, exclude cylinder air, then tighten.
(8)Rod cutting machine handheld hydraulic  when in use, hands should be steady cutting machine, and wear insulated gloves.

GW25 Automatic Bending Machine

GW25 Automatic Bending Machine

GW42E Automatic Bending Machine

GW42E Automatic Bending Machine

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter

GQ50 Rebar Cutter
Introduction:
Reinforcing steel bar cutting machine cuts rebar by converting electric power into kinetic energy through motor. It is durable and of high precision. As a professional rebar cutter supplier, our products can be applied in construction site, steel bar processing factories, road and bridges, etc.
Features:
1.It is with compact structure and good quality.
2. t is easy to move with rolling type truckles.
3.It has outstanding lubricating property, and can be used for over three months continually when getting enough fuel (8-12kg).
4.Reinforcing steel bar cutting machine for diameter 50mm is with low energy consumption as it adopts antifriction bearings with less resistance.
5.It has long working life as it uses high rigidity tool apron and connecting rod.

Rod Cutting Machines，Steel cutting machine，rebar cutting machine，Cutting Machine，Rebar Cutter

Cutting Machine,rebar cutting machine,Steel cutting machine
Introduction:
Steel rod cutting machine can cut round steel 32 times per minute and can be used in construction sites, rebar processing factories, roads and bridges building sites, etc. As a recognized rod cutter supplier, our products are with high cutting speed and long working life.
Features:
1. It has low energy consumption and high performance.
2. Steel rod cutting machine for dia.40mm steel rod is easy to move with rolling type truckles.
3. It has good lubricating property, and can be used for over three months continually when getting enough fuel (8-12kg).
4. It is with low energy consumption as it adopts antifriction bearings with less resistance.
5. Our rod cutters have long working life as it uses high rigidity tool apron and connecting rod.
6. All core components are self produced, which can ensure quality.
7. Gear adopts 500 nodular cast iron, which ensures it can work under heavy load.

Why Choose Rod Cutting Machine from FengYiDa Machinery?

GW50A Automatic Bending Machine

GW50A Automatic Bending Machine

Multi-model stick cutter

Multi-model stick cutter

GW60 Manual Bending Machine

GW60 Manual Bending Machine

Automatic Bending Machine

Automatic Bending Machine

Steel cutting machine

Steel cutting machine

steel bar cutting machine

steel bar cutting machine

RB-25 Automatic Bending Machine

RB-25 Automatic Bending Machine

GT4-12 CNC Rebar

GT4-12 CNC Rebar

video 20141205 101244

Dynamic performance steel cutting machine

Steel cutting machine adopts equivalent mechanical model for dynamic behavior of steel cutting machine to study the mechanical equations of motion derived steel cutting machine; CosmosWorks limited use design analysis software to build steel cutter body finite element model to calculate the cutter body the force, the analysis rebar Cutters body stress distribution of steel cutter body strength check and design checks.